Mã Báo Lỗi Error Code Máy in A0 HP Designjet T1200 44'' (A0) Printer (CH538A)

Các mã báo lỗi error code, của máy in khổ lớn A0 HP T1200 44'' được giới thiệu bởi phòng đào tạo Công Nghệ Siêu Việt tới các bạn kỹ thuật, người sử dụng để làm tài liệu tham khảo sửa chữa.

Mã Báo Lỗi Error Code Máy in A0 HP Designjet T1200 44'' (A0) Printer (CH538A)

Máy in A0 HP T1200 44'' với hỗ trợ ngôn ngữ PostScript - Adobe PostScript 3

• Giới Thiệu Tổng Quan Về Máy In HP DesignJet T1200 44'' A0

- Key Features - Tính năng chính

- Adobe PostScript 3 - Ngôn ngữ in

- Compatible with Windows and Macintosh - tương thích với HĐH Windows và Macintosh

- Exciting detail with 0.02mm minimum line width - Độ rộng đương vẽ tối thiểu là 0,02 mm

- Highly precise drawings with 0.1% line accuracy - Độ chính xác dòng 0.1%

- Print two A1 - sized prints per minute using Economode print setting 

- Up to 2400 x 1200 optimised dpi - Độ phân giải

- Technology: HP Thermal Inkjet - Công nghệ in ấn

- Smart switching, saving time and paper with 2 online rolls, and enabling unattended printing - 2 cuộn giấy chuyển đổi thông minh

- Print continuously with HP matt black ink 300ml cartridges and media length treacking - hộp mực dung tích lớn 300ml

- Optimise blue prints using the new printing mode for generic natural tracing paper. 

- Memory: Standard 384 MB RAM and 160 GB HD - bộ nhớ tiêu chuẩn 384 MB Ram, ổ cứng 160 GB

MÃ BÁO LỖI ERROR CODE

• 60.2:YZ

Initialisation error.

Switch the power OFF from the back of the printer and disconnect the power cord. Check that the printer is properly connected in all other respects. Reconnect the power cord and power ON the printer. 

If error continues then requires a Service Engineer.

• 01.01:YZ

Error in the Main PCA.

Switch the power OFF from the back of the printer and disconnect the power cord. Reconnect the power cord and power ON the printer. 

If error continues then requires a Service Engineer.

• 01.0:YZ

Communication with Main PCA failed.

Switch the power OFF from the back of the printer and disconnect the power cord. Reconnect the power cord and power ON the printer. 

If error continues then requires a Service Engineer.

• 01.2:YZ

Failure communicating with an Ink Supply.

Switch the power OFF from the back of the printer and disconnect the power cord. Reconnect the power cord and power ON the printer. 

If error continues then requires a Service Engineer.

• 02.1:YZ

Problem with Carriage PCA.

Switch the power OFF from the back of the printer and disconnect the power cord. Reconnect the power cord and power ON the printer. 

If error continues then requires a Service Engineer.

• 03.0:10

Battery of Real Time Clock run down.

Requires a Service Engineer.

• 03:YZ

Problem with Power Supply Unit.

Switch the power OFF from the back of the printer and disconnect the power cord. Reconnect the power cord and power ON the printer. 

If error continues then requires a Service Engineer.

• 06:YZ

Failure Reading/Writing NVM in Hard Disk.

Switch the power OFF from the back of the printer and disconnect the power cord. Reconnect the power cord and power ON the printer. 

If error continues then requires a Service Engineer.

• 11:YZ

Trailing Cable does not seem to be detected.

Switch the power OFF from the back of the printer and disconnect the power cord. Reconnect the power cord and power ON the printer. 

If error continues then requires a Service Engineer.

• 21.1:YZ

Failure moving the Primer Motor of the Service Station.

Requires a Service Engineer.

• 21.2:YZ

Failure testing the length of the Service Station path.

Switch the power off from the back of the printer and disconnect the power cord. Check the Primer Tubes. Reconnect the power cord and power on the printer. Make sure that the Service Station path is clear. Remove any visible obstacles (paper, screws, plastic parts, etc.) restricting the movement of the Service Station. 

If error continues then requires a Service Engineer.

• 21:YZ

Failure moving Service Station.

Switch the power OFF from the back of the printer and disconnect the power cord. Make sure that the Service Station path is clear. Remove any visible obstacles (paper, screws, plastic parts, etc.) restricting the movement of the Service Station. Reconnect the power cord and power ON the printer. 

If error continues then requires a Service Engineer.

• 22.0:YZ

Left Ink Supply Error, module 0.

Switch the power off from the back of the printer and disconnect the power cord. Reconnect the power cord and power on the printer. 

If error continues then requires a Service Engineer.

• 22.1:YZ

Left Ink Supply Error, module 1.

Switch the power OFFfrom the back of the printer and disconnect the power cord. Reconnect the power cord and power ON the printer. 

If error continues then requires a Service Engineer.

• 24:YZ

Ink Setup failure.

Switch the power OFF from the back of the printer and disconnect the power cord. Reconnect the power cord and power ON the printer. 

If error continues then requires a Service Engineer.

• 26:01

Ink supply error found during IDS diagnostic test. In the Touch Control Panel you wil see letters reresenting the names of the colours of the faulty supplies.

Reseat the faulty ink supply and repeat the Ink Delivery System diagnostic test. If the problem persists, replace the faulty ink supply and repeat the Ink Delivery System diagnostic test. 

If error continues then requires a Service Engineer.

• 39.1:01

Roll 1 switch failed (standby or resume). Roll 1 has been unloaded.

There is no corrective action. This system warning code only notifies the user that the roll has been unloaded because an unexpected error occurred with Roll 1 in standby or resume operation.

• 39.2:01

Roll 2 switch failed (standby or resume). Roll 2 has been unloaded.

There is no corrective action. This system warning code only notifies the user that the roll has been unloaded because an unexpected error occurred with Roll 2 in standby or resume operation.

• 41:YZ

Electrical fault or current limit in Media-Axis Motor.

Switch the power OFF from the back of the printer and disconnect the power cord. Reconnect the power cord and power ON the printer. Open the Window and check for any visible obstacles restricting the movement of the Media Advance Roller. If there is a wrinkled mass of media inside the paper path, lift the Pinch wheels (using Media Lever) and clear the obstruction. 

If error continues then requires a Service Engineer.

• 42:YZ

Electrical problem (fault, current limit, overheating) in Scan-Axis Motor.

Switch the power OFF from the back of the printer and disconnect the power cord. Reconnect the power cord and power ON the printer. Open the Window and check for any visible obstacles restricting the movement of the Carriage Assembly. Remove any obstacle to let the carriage move freely along the whole scan axis. If there is a wrinkled mass of media inside the paper path, raise the pinch wheels (using the media lever) and clear the obstruction.

If error continues then requires a Service Engineer.

• 45.1:YZ

An error with the Rewinder 1 System (Upper Rewinder) has been detected.

Switch the power OFF from the back of the printer and disconnect the power cord. Remove the paper from Roll 1. Reconnect the power cord and power ON the printer. 

If error continues then requires a Service Engineer.

• 45.2:YZ

An error with the Rewinder 2 System (Lower Rewinder) has been detected (T1200 series only)

Try the following: Switch the power off from the back of the printer and disconnect the power cord. Remove the paper from Roll 2. Reconnect the power cord and power on the printer. If error code recurs requires Service Engineer

• 47:YZ

Starwheels Motor error.

Switch the power OFF from the back of the printer and disconnect the power cord. Remove the paper from Roll 1. Reconnect the power cord and power ON the printer. 

If error continues then requires a Service Engineer.

• 48:YZ

PPS system failure.

Switch the power OFF from the back of the printer and disconnect the power cord. Reconnect the power cord and power ON the printer. 

If error continues then requires a Service Engineer.

• 51:YZ

Window Sensor failure.

Requires a Service Engineer.

• 52:10

The product has detected a failure in the Drop Detector.

Switch the power OFF from the back of the printer and disconnect the power cord. Reconnect the power cord and power ON the printer. 

If error continues then requires a Service Engineer.

• 55:YZ

Problem with the Line Sensor. The product has detected a failure to access the Line Sensor EEPROM.

Switch the power OFF from the back of the printer and disconnect the power cord. Reconnect the power cord and power ON the printer. 

If error continues then requires a Service Engineer.

• 56:YZ

Drive Roller analog encoder homing (also known as "zero search") failed.

Switch the power OFF from the back of the printer and disconnect the power cord. Reconnect the power cord and power ON the printer. 

If error continues then requires a Service Engineer.

• 59.1:09

Two electrical parts have been replaced at the same time.

Requires a Service Engineer

• 59.2:00

An unsupported or used part has been installed.

Requires a Service Engineer.

• 60.1:YZ

Initialisation error.

Switch the power OFF from the back of the printer and disconnect the power cord. Check that the printer is properly connected in all other respects. Reconnect the power cord and power ON the printer. 

If error continues then requires a Service Engineer.

• 61:04.1

The PostScript fonts seem to be missing.

Requires a Service Engineer to Perform a firmware upgrade to re-install the fonts.

• 61:08.1

The file cannot be printed because it is password protected.

Resend the file without password protection.

• 61:YZ

The file format is incorrect or not supported for the current product configuration and the product cannot process the job.

Check whether the printer supports the file format (formats such as PS, PDF, TIFF and JPEG are supported by PostScript printers only). Switch the power OFF from the back of the printer and disconnect the power cord. Reconnect the power cord and power ON the printer. Resend the file to the printer. If error continues then requires a Service Engineer.

• 63:YZ

Input/Output problem through the network interface of the formatter.

Switch the power OFF from the back of the printer and disconnect the power cord. Reconnect the power cord and power ON the printer. 

If problem continues may require a Service Engineer.

• 64.1:YZ

Printer does not ecognise the USB HDD accessory connected.

Switch the power OFF from the back of the printer and disconnect the power cord. Reconnect the power cord and power ON the printer. 

If error continues then requires a Service Engineer.

• 64:YZ

Input/Output problem through the USB Port.

Switch the power OFF from the back of the printer and disconnect the power cord. Reconnect the power cord and power ON the printer. 

If error continues then requires a Service Engineer.

• 65:YZ

Memory Driver Internal I/O Socket Manager Internal I/O error.

Switch the power OFF from the back of the printer and disconnect the power cord. Reconnect the power cord and power ON the printer. 

If error continues then requires a Service Engineer.

• 68:YZ

Loss of engine counters tracking.

Requires a Service Engineer.

• 71:03

Out of Memory.

Restart the printer. 

If error continues then requires a Service Engineer.

• 71:04

Out of Memory.

Restart the printer. 

If error continues then requires a Service Engineer.

• 72.02:YZ

A service calibration should be performed.

Requires a Service Engineer.

• 74.1:YZ

Error uploading media profile update file.

Switch the power OFF from the back of the printer and disconnect the power cord. Ensure that the connection between the computer is functioning correctly. Reconnect the power cord and power ON the printer. 

If error continues then requires a Service Engineer.

• 74:YZ

Error uploading Firmware update file.

Requires a Service Engineer.

• 75.21:YZ

The Spitoons (Left Spitton, Service Station) have reached 80% capacity.

Requires a Service Engineer.

• 75.22:YZ

The Spitoons (Left Spitton, Service Station) are full.

Requires a Service Engineer.

• 76:YZ

Hard disk drive is full.

Remove any unnecessary files from the hard disk using the Embedded Web Server. 

If problem continues requires a Service Engineer.

• 78.1:YZ

Media settings area missing in paper settings file. 

Switch the power off from the back of the printer and disconnect the power cord. Reconnect the power cord and power on the printer. If problem continues requires a Service Engineer.

• 78:08

The job received cannot be printed without borders on this paper.

Use a paper that supports borderless printing.

• 79:YZ

Generic firmware Error.

Switch the power OFF from the back of the printer and disconnect the power cord. Reconnect the power cord and power ON the printer. 

If problem continues requires a Service Engineer.

• 81:YZ

This Error can occur if the product has been dropped during transportation causing structural damage.

This error can occur because the printer has been dropped during transportation, causing structural damage. 

Try to verify any structural damage, requires a Service Engineer.

• 86:01

Possible Paper jam.

Open the Window and check for any visible obstacles restricting the movement of the Drive Roller. Remove any such obstacles. If there is a wrinkled mass of media inside the paper path, lift the Pinch wheels (using the Media Lever) and clear the obstruction. 

If problem continues requires a Service Engineer.

• 86:11

Scan axis movement requires too much force or energy.

Requires a Service Engineer.

• 87:01

Problem finding the Scan-axis encoder reading.

Switch the power OFF from the back of the printer and disconnect the power cord. Reconnect the power cord and power ON the printer. 

If problem continues requires a Service Engineer.

• 87:YZ

Problem with Carriage Encoder Sensor readings.

Requires a Service Engineer.

• 93:YZ

Unable to pressurise the Ink Delivery System.

Switch the power OFF from the back of the printer and disconnect the power cord. Reconnect the power cord and power ON the printer. 

If problem continues requires a Service Engineer.