Mã Báo Lỗi Error code Máy In HP Designjet 800 42'' (A0) Printer (C7780B)

Mã Báo Lỗi Error code Máy In HP Designjet 800 42'' (A0) Printer (C7780B)

Mã báo lỗi của máy in HP DesignJet 800 42'', được cung cấp bởi trung tâm sửa chữa bảo hành máy in khổ lớn HP - Công Nghệ Siêu Việt.

Mã Báo Lỗi Error code Máy In HP Designjet 800 42'' (A0) Printer (C7780B)

Thông Tin Máy In HP DesignJet 800 42''

DesignJet 800 42 inch

Key Features:

- Print languages: HP-GL/2, HP RTL, CALS G4 (TIFF and JPEG files from UNIX®, Linux and Windows NT via ZEHRaster Plus)

- Standard Memory 96 MB / Maximum Memory 160 MB (w/ HP-GL/2 accessory card), 6 GB HD

- Windows and Macintosh drivers

- HP Jetdirect internal EIO print server

- 2400 x 1200 dpi

- Best combination of line quality and image printing. Four-colour, high-resolution writing system with pigmented black delivers excellent line quality plus high quality imaging

- Workgroup printers are designed to be shared with a virtual computer inside for on-board processing, built-in networking, a hard drive, and support for file queuing and nesting.

Danh Sách ERROR CODE

01:10

Electronics Module failure.
Requires Service Engineer

01:11

The Electronics Module Cooling Fan badly connected.
Switch the Printer Off and wait a few minutes. Switch the Printer On again and check if the Error Code has disappeared.
If the Error Code continues, requires Service Engineer

01:12

The EEROM is not configured correctly (the product number may be missing).
Requires Service Engineer

01:13

Electronics Module failure.
Switch the Printer Off and wait a few minutes. Switch the Printer On again and check if the Error Code has disappeared.
If the Error Code continues, requires Service Engineer

02:10

Carriage failure.
Requires Service Engineer

02:13

Carriage failure.
Switch the Printer Off and wait a few minutes. Switch the Printer On again and check if the Error Code has disappeared.
If the Error Code continues, requires Service Engineer.

03:10

Power Supply failure.
Requires Service Engineer

04:11

LAN Card not detected.
Requires Service Engineer
05:10 (Only applicable to DJ 800 Series)
Formatter failure Error/Formatter not detected Warning.
Requires Service Engineer

05:11

Formatter not detected.
Requires Service Engineer

08:11

Front Panel cannot be detected.
Requires Service Engineer

11:11

Trailing Cable badly connected.
Requires Service Engineer

11:13

Problem with setting the voltage of the Printheads.
Requires Service Engineer

12:11

A short detected in the Carriage Assembly.
Requires Service Engineer

21:10

Service Station failure.
Requires Service Engineerhp designjet

21:11

Service Station/Aerosol Fan cannot be detected or the Service Station is badly adjusted.
Requires Service Engineer

22:10

Ink Supply Station failure.
Requires Service Engineer

41:10

Paper-Axis Motor failure.
Requires Service Engineer

41:13

Error in the Paper-Axis Motor Encoder quadrature.
Requires Service Engineer

42:10

Scan-Axis Motor failure. 
Requires Service Engineer

43:10

Vacuum Fan failure.
Requires Service Engineer

43:11

Vacuum Fan not detected.
Requires Service Engineer

56:10

Drive Roller Encoder Sensor error.
Requires Service Engineer

56:13

Error in the Drive Roller Encoder Sensor quadrature.
Switch the Printer Off and wait a few minutes. Switch the Printer On again and check if the Error Code has disappeared. If the Error Code continues Requires Service Engineer

61:04

Firmware Error.
Switch the Printer Off and wait a few minutes. Switch the Printer On again and check if the Error Code has disappeared. If the Error Code continues Requires Service Engineer

61:05

Error Processing Job. This Error Code only appears in HP DesignJets 800 Series, or in the HP DesignJet 500 Series with an HP-GL/2 card installed, when processing either a PostScript or HP-GL/2 file.
Switch the Printer Off and wait a few minutes. Switch the Printer On again and resend the file that you were trying to print. If the Error Code reappears after resending the file, then try generating the file again and try to print again. If the Error Code continues Requires Service Engineer

64:04

Firmware Error (USB Port).
Switch the Printer Off and wait a few minutes. Switch the Printer On again and check if the Error Code has disappeared.
If the Error Code reappears, requires a Service Engineer.

71:04

Problem allocating Memory. This Error Code only appears in HP DesignJets 800 Series, or in the HP DesignJet 500 Series with an HPGL/ 2 card installed.
Switch the Printer Off and wait a few minutes. Switch the Printer On again and check if the Error Code has disappeared. If the Error Code reappears, requires a Service Engineer.

71:06

Out of Memory problem. This Error Code only appears in HP DesignJets 800 Series, or in the HP DesignJet 500 Series with an HP-GL/2 card installed, when processing either a PostScript or HPGL/ 2 file.
Requires Service Engineer

72:04

Problem in the Scan-Axis (Firmware Error).
Switch the Printer Off and wait a few minutes. Switch the Printer On again and check if the Error Code has disappeared. If the Error Code reappears, requires a Service Engineer.

73:04

Servo Error.
Switch the Printer Off and wait a few minutes. Switch the Printer On again and check if the Error Code has disappeared.
If the Error Code reappears, requires a Service Engineer.

79:04

Firmware Error.
Switch the Printer Off and wait a few minutes. Switch the Printer On again and check if the Error Code has disappeared. If the Error Code reappears, requires a Service Engineer.

81:01

Paper-Axis shutdown.
If this error code appeared but was NOT caused by a paper jam, then requires a Service Engineer.

81:11

Paper-Axis shutdown (during the Paper Advance test).
Requires Service Engineer

85:10

Paper-Axis Encoder error. The Drive Roller Encoder Sensor cannot find the zero position of the Encoder Disk.
Requires Service Engineer

86:01

View on View on YouTube
Carriage-Axis shutdown.
If this error code appeared but was NOT caused by a paper jam, then Requires a Service Engineer

86:11

View on View on YouTube
Carriage-Axis shutdown (during the Carriage Movement test).
Requires Service Engineer

86:13

Carriage-Axis shutdown (Firmware Error).
Switch the Printer Off and wait a few minutes. Switch the Printer On again and check if the Error Code has disappeared. If the Error Code reappears, requires a Service Engineer

87:13

Unable to read the Carriage Encoder Sensor.
Switch the Printer Off and wait a few minutes. Switch the Printer On again and check if the Error Code has disappeared. If the Error Code reappears, requires a Service Engineer.

93:10

Ink System startup failed.
Requires Service Engineer